• DJI F550 with Naza Light flight controller with GPS
  • DJI F550 Flamewheel (E310) with Naza Light v1.1 + GPS Quadcopter Package
  • DJI F550 Flamewheel (E310) with Naza Light v1.1 + GPS Quadcopter Package
  • DJI F550 Flamewheel (E310) with Naza Light v1.1 + GPS Quadcopter Package
  • DJI F550 Flamewheel (E310) with Naza Light v1.1 + GPS Quadcopter Package

DJI

DJI F550 Flamewheel (E310) with Naza Light v1.1 + GPS Quadcopter Package

£299.99

Not available in store Not available online
delivery

FREE SHIPPING,On Orders Over £399.99

See terms & conditions*
 

DETAILS:

With more efficient motors and intelligent ESCs, this package offers you more information while flying and makes each flight last longer. Built for multirotors with a diagonal base of 330-350mm. Built for multirotors weighing 1-2.5kg.

FlameWheel series is multi-rotor frame designed for all pilots for fun or AP. With DJI WKM or NAZA autopilot system, it can achieve hovering, cruising, even rolling and other flight elements. It can be applied for entertainment, aerial photography, FPV and other aeromodelling activities.

We have a range of packages for the F550 Flamewheel from the basic kit with motors and speed controllers right through to fully working with brushless camera gimbal for the Gopro 3.

Included with the Flamewheel:

  • 1x Frame set.
  • 6x 15 Amp E310 Speed controllers.
  • 6x E310 2212 920kva Motors
  • 8x E310 9" Self tightening props (cw/ccw)
  • DJI Flight Controller Naza Light V1.1 with GPS
  • Extended landing legs


Note: These products are not assembled when shipped. Users must solder and assemble before flying

NAZA LITE FEATURES:

  • All-in-One Design
  • Advanced attitude stabilize Algorithm
  • Multiple flight control mode/intelligent switching
  • GPS Module Available/Accurate Position hold
  • Intelligent Orientation Control (IOC)
  • Failsafe mode
  • Low voltage protection
  • Motor Arm and Motor Dis-arm
  • Support Futaba S-Bus and PPM receiver
  • Supported multi-rotor types

REQUIRED TO COMPLETE:

  • 5-8 channel 2.4ghx transmitter and receiver. (one of the channels needs to be a three position switch}
  • LiPo battery, 11.1v/14.4v 3350 - 6100mah 3/4s 30c. (if you are using a camera gimbal, we recommend the 6100mah)
  • LiPo Charger.


Model is supplied as a kit and requires building. You will need a soldering iron, solder and tiewraps. Picture shows assembled model for reference only. Can be supplied assembled on request.

BUILDING SERVICE:

Fast building service from £29.99, Lead time 2-7 days depending on level of completeness.

We can build your Flamewheel for you which would include all the assembly of the frames and control unit, radio system, gimbals, FPV. Basically everything you buy along with your quadcopter frame kit.

The two build options we offer are:

  1. Frame & Flight Controller: We will build the frame which includes all soldering and fitting of connectors (XT60), Fit the flight controller of your choice leaving you the fitting of the radio either your own or supplied by us.
  2. Frame, Flight Controller, Radio and Accessories. So we do the same as above but also fit ther adio supplied by us and any other accessories bought along side such as gimbals, FPV Ground station etc. We fully calibrate and flight test so its ready to go.

All our builds are covered by our extended email support hours (M-F (9:30am to 10.30pm)

INSTRUCTIONAL VIDEO: